<object id="gx5sy"><dd id="gx5sy"><dl id="gx5sy"></dl></dd></object><li id="gx5sy"></li>
    <form id="gx5sy"></form>
        <form id="gx5sy"><pre id="gx5sy"></pre></form><center id="gx5sy"></center>
        <form id="gx5sy"><legend id="gx5sy"></legend></form>
        <wbr id="gx5sy"></wbr>
      1. <sub id="gx5sy"></sub>

      2. <form id="gx5sy"></form>

        德成鋁業

        您的位置:首頁 > 新聞資訊 >

        防銹鋁板要具備的制作要點

        來源:http://www.kongyh.com

        1、貯存:應將防銹鋁板存放于干燥通風處,且平放在平整的表面上,切勿踩踏、撞擊。
        1, storage: the antirust aluminum plate should be stored in the dry and ventilated place, and flat on the surface of the flat, do not trample or impact.
        2、搬運:搬運板材應將板的四邊同時抬起,嚴禁推拉、抽取,以免刮傷板面。
        2, handling: moving plate should lift the four sides of the plate at the same time, strictly prohibit pushing and pulling, so as to avoid scraping the surface of the plate.
        3、開槽:用開槽機或鑼機開槽時,應使用半圓頭式大于90度的銑刀.下刀既不要過深傷及防銹鋁板,也不要過淺使折邊困難,應留有0.2-0.3MM厚塑料芯材連同鋁板一起彎邊,以增加強度和韌性,否則在彎邊時鋁板可能斷裂或漆膜爆裂。
        3, use: slotted slotting machine or gong machine slot, should use more than 90 of the cutter head semicircle. The knife is not too deep and antirust aluminum, not too shallow to hem difficulties, should be 0.2-0.3MM thick plastic core material with aluminum plate bending together, in order to increase the strength and toughness, not in bending the plate or film may burst fracture.
        4、彎邊:彎邊時需用力均勻,一次成型,不要反復彎折,否則防銹鋁板可能斷裂。
        4, bending edge: when the edge must be forced evenly, one molding, do not bend repeatedly, otherwise the antirust aluminum plate may break.

        鋁卷生產廠家
        5、弧形加工:加工弧形應使用專用彎曲設備加工,徐徐用力,使板材逐步達到所需的曲面.切勿一次彎曲成型。
        5, arc processing: processing arc should be processed with special bending equipment, so that the plank will gradually reach the required surface.
        6、批次:同一型號而不同批次的板材可能存在色差,不同色差的防銹鋁板價格可能不同,出售和使用不同批次板材時應增加比對色差之程序,無視覺色差時方可在同一平面使用。
        6, batch: the same type and different batches of plates may have chromatic aberration. The price of rust proof aluminum plates with different chromatic aberrations may be different. When selling and using different batches of plates, we should increase the procedure of comparing chromatic aberration. When no color difference is observed, they can be used in the same plane.
        7、安裝方向:將同色鋁板安裝在同一平面時,流程方向應一致,否則可能造視覺色差。
        7, installation direction: when the same color aluminum plate is installed on the same plane, the direction of the process should be consistent, otherwise the visual color difference may be made.
        8、撕膜:應在防銹鋁板安裝后的45天內撕去保護膜,否則可能發生撕膜困難或移膠現象。
        8, tear film: the protective film should be tore out within 45 days after the installation of antirust aluminum plate, otherwise it may be difficult to tear film or remove glue.
        9、使用條件:內墻板應在室內使用,不宜安裝在室外,以保證使用效果和使用年限。
        9, use conditions: the inner wall board should be used indoors, not in the outdoor, so as to ensure the use effect and the service life.

        友情链接:  2019在线情侣自拍视频 {关键词}
        http:// qu6 临沧市| 本溪市| 巩留县| 南川市| 宽甸| 舒城县| 甘泉县| 汶川县| 周宁县| 天峻县| 扎兰屯市| 延寿县| 梁平县| 大余县| 宜宾县| 章丘市| 崇明县| 安乡县| 清水河县| 武强县| 新化县| 波密县| 湛江市| 紫阳县| 松江区| 益阳市| 梓潼县| 双城市| 广灵县| 科技| 淮阳县| 梨树县| 丹巴县| 宁城县| 深圳市| 罗甸县| 咸阳市| 宜州市| 招远市| 阿拉善盟|