<object id="gx5sy"><dd id="gx5sy"><dl id="gx5sy"></dl></dd></object><li id="gx5sy"></li>
    <form id="gx5sy"></form>
        <form id="gx5sy"><pre id="gx5sy"></pre></form><center id="gx5sy"></center>
        <form id="gx5sy"><legend id="gx5sy"></legend></form>
        <wbr id="gx5sy"></wbr>
      1. <sub id="gx5sy"></sub>

      2. <form id="gx5sy"></form>

        德成鋁業

        您的位置:首頁 > 新聞資訊 >

        濟南德成鋁業5052鋁板的生產流程有哪些?

        來源:http://www.kongyh.com

        5052鋁板的生產工藝通過這幾進程:配料--切開--刨槽--切角--折彎--組板--加筋--復檢.
        5052 aluminum plate production process through these processes: ingredients - cut - cut - planer - cut angle - bending - group board - reinforcement - reinspection.
        配料:按工廠所接的單,進行資料型號、規格、色澤的選擇,以后運到切開機前待切開.
        Ingredients: select the data type, specification, color and lustre according to the list of the factory. It will be cut before cutting to the cutting machine.
        切開:進行切開時,先將定位器調到所需的尺度,先切一小點后,復核尺度是不是與需求尺度相契合,相符時開始切開,反之進行調整,直至契合停止.在切開時,方向要準確.從左向右、從上至下,禁絕反切;切開結束時進行校驗,看看是不是契合規范,以后將板塊輕放于清潔渠道清潔,防止板塊飾面受損.
        Open: open, first locator to the required scale, first cut a small scale after the review is not fit with the demand scale, began to open match, and adjusted to fit in until stop. And, to be exact. The direction from left to right, from top to bottom, from Fanqie; open check at the end to see is not meet the standards will be gently on the plate clean clean channel, to prevent the plate facing damage.
        刨槽:刨槽時要注意的是必須將加工單圖意作再次剖析、確認、定型.

        鋁板生產廠家
        Planer: the planer should pay attention to the need to re analyze, confirm and shape the processing chart.
        切角:沖角機上沖切,切角不允許超越刨槽中心線.
        Cutting angle: the punching angle machine is washed and the cutting angle is not allowed to surpass the center line of the planing slot.
        折彎:要注意不能重復的進行折彎,較多折彎兩次,防止疲勞損壞.
        Bending: to be careful not to repeat the bending, maximum bending two times, to prevent fatigue damage.
        組板、加筋:首要準備好組板的資料及東西,要注意組板進程不能損害板塊飾面.
        Group board, reinforcement: the first preparation of the data and things of the board, it is necessary to pay attention to the board process can not damage the plate decoration.
        復檢:進行對竣工的5052鋁板進行復檢,看看是不是契合制造規范,防止在出廠時給廠家帶來不好的作用.
        Recheck: carry on the reinspection of the completed 5052 aluminum plate to see if it fits the manufacturing specification and prevents the factory from bringing bad effect to the factory when it comes out.
        以上內容就是鋁板生產廠家為大家整理的分享,更多的精彩內容請進入: http://www.kongyh.com 我們會有專人為您解答,你的支持是對我們工作更好的支持!
        The above content is the aluminum plate manufacturer's arrangement for you to share, more wonderful content, please enter: http://www.kongyh.com, we will have someone to answer for you, your support is better support for our work.

        友情链接:  2019在线情侣自拍视频 {关键词}
        http:// 6wt 河源市| 阿图什市| 乐山市| 明水县| 宝鸡市| 治多县| 阿克陶县| 容城县| 民权县| 商都县| 彭阳县| 资中县| 丘北县| 通化市| 黄大仙区| 叶城县| 武汉市| 郯城县| 徐闻县| 余姚市| 大同县| 吴川市| 贵德县| 丰城市| 宁化县| 常德市| 海口市| 崇文区| 南投县| 敦煌市| 旅游| 疏附县| 洛川县| 京山县| 额济纳旗| 肥东县| 海门市| 池州市| 光山县| 宁阳县|